My hot water heater needed replacement. Deanna was very pleasant, knowledgeable, and most helpful. She scheduled my appointment and James M. and Aaron arrived exactly on time. They were professional and had the job done in no time! Although it was a bit more expensive than I was expecting, the service was excellent. Thank you for a job well done.
According to standards set by the federal government, a low-flow showerhead uses no more than 2.5 gallons of water per minute at a water pressure of 80 pounds per square inch. That’s less than half the rate of water used by some older traditional showerhead models. Low-flow showerheads come in two main types, aerating, which creates a mist, or laminar-flow that sends water out in a steady stream.
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.
We provide emergency plumbing service to Atlanta and the surrounding communities, including: Acworth, Alpharetta, Austell, Avondale Estates, Brookhaven, Buford, Chamblee, Clarkston, Conyers, Cumming, Dacula, Decatur, Doraville, Douglasville, Duluth, Dunwoody, Fayetteville, Forest Park, Grayson, Holly Springs, Johns Creek, Kennesaw, Lawrenceville, Lilburn, Lithonia, Loganville, Marietta, Milton, Morrow, Norcross, Peach Tree City, Pine Lake, Powder Springs, Roswell, Sandy Springs, Snellville, Stone Mountain, Sugar Hill, Suwanee, and Woodstock, GA.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
We have used Atomic multiple times and every time they have done a phenomenal job! We've had 2 different plumbing specialist, both named Justin, and each have been wonderful and knowledgeable in helping us with our problems. Our most recent issue was a leaking service line. Atomic had Justin D. to my house at 7pm, and was able to schedule me for next day repairs! I will only use and recommend Atomic as my plumbing service!
Most recently they sent Mike out to snake a kitchen sink drain for us. Mike got here earlier than quoted and got the work done quickly so I could get out of work on time and pick up my little boy from daycare. I called them back to give a compliment about Mike. I like to let them know when they do a good job. Mike was really a great guy. I have nothing but good things to say about them. When we have an issue we call them. Their techs are personable and always make the residents laugh. They are clean and well prepared. It is a real stand up operation.
Robert is knowledgeable, respectful and arrived within the time parameters he told me he would. He clearly communicated our problem to us and is working diligently to rectify it. I have to add, cleanliness in our household is of the utmost importance and Robert is meticulous with his work and pretty much left no trace of his presence when he was done. That part of the service in and of itself is invaluable.
Present-day water-supply systems use a network of high-pressure pumps, and pipes in buildings are now made of copper, brass, plastic (particularly cross-linked polyethylene called PEX, which is estimated to be used in 60% of single-family homes), or other nontoxic material. Due to its toxicity, most cities moved away from lead water-supply piping by the 1920s in the United States, although lead pipes were approved by national plumbing codes into the 1980s, and lead was used in plumbing solder for drinking water until it was banned in 1986. Drain and vent lines are made of plastic, steel, cast-iron, or lead.
James and Paul did an AWESOME job from start to finish with our toilet replacement and installation!! We unfortunately had a bad experience with our general contractor and his plumber and needed immediate assistance. I called Atomic and they immediately got me connected with a scheduler, then had James and Paul out to our house extremely fast! James and Paul were friendly, knowledgeable, professional, and efficient. They advised us based on their expertise and helped us pick out a new toilet and install it correctly. We are so grateful for their work and their professionalism. Would highly recommend them and hire them again!
Plumbing Service Co