Wooden pipes were used in London and elsewhere during the 16th and 17th centuries. The pipes were hollowed-out logs, which were tapered at the end with a small hole in which the water would pass through.[16] The multiple pipes were then sealed together with hot animal fat. They were often used in Montreal and Boston in the 1800s, and built-up wooden tubes were widely used in the USA during the 20th century. These pipes, used in place of corrugated iron or reinforced concrete pipes, were made of sections cut from short lengths of wood. Locking of adjacent rings with hardwood dowel pins produced a flexible structure. About 100,000 feet of these wooden pipes were installed during WW2 in drainage culverts, storm sewers and conduits, under highways and at army camps, naval stations, airfields and ordnance plants.

Similarly, there's no shortage of different types of sinks, too. These range from spare single-bowl models starting under $100 to a farmhouse apron front, double bowl made of copper or cast iron that can run $600 or more. Some are mounted under countertops — called undermount sinks — while drop-in sinks are designed for installation in a preexisting space in your countertop. Whatever the type, sinks can uniquely complement kitchen design as do countertops, cabinetry and other features.


According to standards set by the federal government, a low-flow showerhead uses no more than 2.5 gallons of water per minute at a water pressure of 80 pounds per square inch. That’s less than half the rate of water used by some older traditional showerhead models. Low-flow showerheads come in two main types, aerating, which creates a mist, or laminar-flow that sends water out in a steady stream.
For details about apprenticeship or other opportunities in this occupation, contact the offices of the state employment service; the state apprenticeship agency; local plumbing, heating, and cooling contractors or firms that employ fitters; or local union–management apprenticeship committees. Apprenticeship information is available from the U.S. Department of Labor's Apprenticeship program online, or by phone at 877-872-5627.
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).[17]
Prices as quoted ($500-781) OBVIOUSLY included the cost of the toilet. In my quote request I stated project was a totally unremarkable - removal of old toilet and install of the new toilet, which I will have purchased myself. There are no problems and this is not an old house. Simply want t upgrade from contractor grade toilet. I am a retired contractor with a bad back and I know what the project entails.

When you are faced with a plumbing emergency, time is of the essence. You don’t want to have to spend time searching for a plumber near you that is open nights, weekends, and holidays that won’t charge you exorbitant fees for immediate availability to address plumbing emergencies. Roto-Rooter plumbers offer a variety of emergency plumbing services around the clock at an affordable price, so you can get the plumbing services you need at a price that won’t break the budget.
Called at 2pm and had service completed by 6pm on a cold any busy day with lots of frozen pipes. Extremely fast and took the time to communicate both the issue, and associated costs of repair. Also very communicative for when someone would be by. Got an update call from the service center saying “we are a bit busy but you are still in the schedule for today”. Much appreciated so I could plan my afternoon while waiting. Highly recommended.
According to standards set by the federal government, a low-flow showerhead uses no more than 2.5 gallons of water per minute at a water pressure of 80 pounds per square inch. That’s less than half the rate of water used by some older traditional showerhead models. Low-flow showerheads come in two main types, aerating, which creates a mist, or laminar-flow that sends water out in a steady stream.
The Eccotemp EZ-FLUSH System Descaler Kit is the The Eccotemp EZ-FLUSH System Descaler Kit is the answer to any water scale lime or rust deposit buildup in virtually any piece of water based equipment. The EZ-FLUSH system has been designed to work seamlessly with Tankless Water Heaters and is compact for easy use and storage. It includes our ...  More + Product Details Close 

You need the right tools when repairing your plumbing systems or installing new devices. Menards® has a large variety of plumbing tools, including pipe threading; plumbing hand tools; plumbing tool kits; and torches and soldering tools. Keep your drains clean and free of clogs with our drain cleaning equipment and supplies, including hand, chemical, and powered solutions.

Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.


The word "plumber" dates from the Roman Empire.[3] The Latin for lead is plumbum. Roman roofs used lead in conduits and drain pipes[4] and some were also covered with lead, lead was also used for piping and for making baths.[5] In medieval times anyone who worked with lead was referred to as a plumber as can be seen from an extract of workmen fixing a roof in Westminster Palace and were referred to as plumbers "To Gilbert de Westminster, plumber, working about the roof of the pantry of the little hall, covering it with lead, and about various defects in the roof of the little hall".[6] Thus a person with expertise in working with lead was first known as a Plumbarius which was later shortened to plumber.
Although plumbers, pipefitters, and steamfitters perform three distinct and specialized roles, their duties are often similar. For example, they all install pipes and fittings that carry water, steam, air, or other liquids or gases. They determine the necessary materials for a job, connect pipes, and perform pressure tests to ensure that a pipe system is airtight and watertight. Their tools include drills, saws, welding torches, and wrenches.
Our Water Heater failed and flooded our attic on the weekend. They answered the phone and had someone out the same day. By the next day, we had a new water heater installed and hot water, all over the weekend. They were quick and professional. Justin D answered all my questions and took the time to explain. When speaking to Justin it was clear that he cared and was well trained in customer experience. Thank you all for making a stressful situation a little easier to deal with. We appreciate your services.
"We just moved to a new house and Luke did an amazing job installing our home entertainment system. We thought we had a simple TV mounting project, but Luke was able to connect all our equipment (some of which was a bit outdated) so we have one seamless audio/visual system. Plus he was able to fix some errors that Comcast had made and willing to jump in and work on a few other small projects I needed done before the holidays. His price was reasonable and in the week since he performed the work I've had 2 people knowledgeble in contracting or wiring compliment the quality of his work."
Top notch service -- rapid response too!Had a leaky pipe to a washing machine. Called Atomic Plumbing at 8 AM -- they arrived at my house on time and less than 2 hours after my initial call to them. James & Paul were my technicians. Professional, polite, efficient and skilled, they rapidly replaced dated water valves and -- I must say, they did a great job. The repairs not only are functional, but they look great, too!I especially was impressed with the method of pricing. They assess your issue, then provide a flat-fee repair price before any work is done. Their prices are reasonable with no surprises.Highly recommend this company if you want it done right the first time by professionals.
When your plumbing system is not running smoothly, you need a reliable plumber there to assist you as quickly as possible. But you should also find an expert who can help you with all of your plumbing needs over time, whether you want to upgrade your fixtures or add in a new sump pump or water treatment system. Call our professionals whenever you run into urgent plumbing issues, and we can get out there fast to get your pipes and fixtures back in order. Magnolia Plumbing, Heating & Cooling is a trusted name in plumbing repair, installation, maintenance, and replacement in the Washington, DC area, and we can handle whatever plumbing tasks come our way—guaranteed!
Atomic Plumbing is your first call for Virginia Beach, Chesapeake, and Norfolk plumbing needs – residential or commercial. If you have a leaky pipe or drain clog, or wish to install new bathroom fixtures, Atomic Plumbing can help. Our plumbing team is certified and trained to tackle any sewer or drainage problem, using the latest parts and equipment to repair frozen or damaged pipes or faulty water heaters.

Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.

×