Called in on Wednesday evening to schedule a new sink hookup and was put on the schedule for Friday morning with no problems. Ryan arrived and took a look at what I had, gave some recommendations and provided a couple quotes. He took his time and made sure everything he installed was the most efficient and correct for my setup. We will continue to use and strongly recommend Atomic Plumbing.
Wooden pipes were used in London and elsewhere during the 16th and 17th centuries. The pipes were hollowed-out logs, which were tapered at the end with a small hole in which the water would pass through.[16] The multiple pipes were then sealed together with hot animal fat. They were often used in Montreal and Boston in the 1800s, and built-up wooden tubes were widely used in the USA during the 20th century. These pipes, used in place of corrugated iron or reinforced concrete pipes, were made of sections cut from short lengths of wood. Locking of adjacent rings with hardwood dowel pins produced a flexible structure. About 100,000 feet of these wooden pipes were installed during WW2 in drainage culverts, storm sewers and conduits, under highways and at army camps, naval stations, airfields and ordnance plants.
Scott was very knowledgeable and happy to test out all items of my finikie hot water heater. He called in tech support and tested pressures and did a vent pipe test to check air flow. How do I know this, because he explained everything to me. One afternoon with him, and I could be a tech. All joking aside. I appreciate the continued support of Atomic. Scott's professionalism and willingness to keep me in the loop is spot on. Thanks Scott.

When your plumbing system is not running smoothly, you need a reliable plumber there to assist you as quickly as possible. But you should also find an expert who can help you with all of your plumbing needs over time, whether you want to upgrade your fixtures or add in a new sump pump or water treatment system. Call our professionals whenever you run into urgent plumbing issues, and we can get out there fast to get your pipes and fixtures back in order. Magnolia Plumbing, Heating & Cooling is a trusted name in plumbing repair, installation, maintenance, and replacement in the Washington, DC area, and we can handle whatever plumbing tasks come our way—guaranteed!


Len The Plumber is a full service plumbing and drain cleaning company serving the entire Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia Area as well as Anne Arundel, Baltimore, Carroll, Cecil, Harford, Howard, Montgomery, Prince George’s, Charles, Fairfax, Alexandria, Arlington, Loudoun, Prince William, Falls Church, Manassas, Delaware, Chester, New Castle, and Stafford counties. We are continuing to grow and expand our service areas so please continue to check-in to see if we are in your area and always feel free to call if you have a question. Our service area map shows all the counties and district that we currently serve.
Is it time to replace your home’s plumbing? If your home’s plumbing is more than 40 years old, or you are experiencing pinhole leaks or other failures, it is time to talk to Benjamin Franklin Repiping Cedar Rapids and Eastern Iowa. Our plumbers will walk you through the options and repiping process. You’ll appreciate the peace of mind that a new, code compliant, reliable plumbing system provides.
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]
As important as it is that you are able to distribute potable water throughout your home in a dependable manner, it would be a much less convenient state of affairs if you were not also able to dispose of that water just as conveniently, not to mention hygienically. That is why we suggest allowing our Master Plumbers to complete any and all drain and sewer services that you may require. From basic cleanings to complex repairs and eventual replacements, we truly do it all. If you have any reason to suspect a problem with your drain and sewer system, give us a call right away.
Scott was very knowledgeable and happy to test out all items of my finikie hot water heater. He called in tech support and tested pressures and did a vent pipe test to check air flow. How do I know this, because he explained everything to me. One afternoon with him, and I could be a tech. All joking aside. I appreciate the continued support of Atomic. Scott's professionalism and willingness to keep me in the loop is spot on. Thanks Scott.
According to standards set by the federal government, a low-flow showerhead uses no more than 2.5 gallons of water per minute at a water pressure of 80 pounds per square inch. That’s less than half the rate of water used by some older traditional showerhead models. Low-flow showerheads come in two main types, aerating, which creates a mist, or laminar-flow that sends water out in a steady stream.

The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
Plumbers, pipefitters, and steamfitters may use many different materials and construction techniques, depending on the type of project. Residential water systems, for example, use copper, steel, and plastic pipe that one or two plumbers can install. Power plant water systems, by contrast, are made of large steel pipes that usually take a crew of pipefitters to install. Some workers install stainless steel pipes on dairy farms and in factories, mainly to prevent contamination.
Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.

Plumbing Repair

×