James and Paul did an AWESOME job from start to finish with our toilet replacement and installation!! We unfortunately had a bad experience with our general contractor and his plumber and needed immediate assistance. I called Atomic and they immediately got me connected with a scheduler, then had James and Paul out to our house extremely fast! James and Paul were friendly, knowledgeable, professional, and efficient. They advised us based on their expertise and helped us pick out a new toilet and install it correctly. We are so grateful for their work and their professionalism. Would highly recommend them and hire them again!

Plumbing Service Co


Payment schedule: On a big job, especially a planned remodeling, the service provider may want the customer to pay 10 to 15 percent of the cost up front and 50 percent paid before the job is completed — especially if expensive materials need to be purchased for the project. Make sure you know what is expected. If you're suspicious, contact your state's professional licensing board or contracting board to ask about local standards. Many states set limits on what is allowed to be paid upfront.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
Mounted under the sink, the garbage disposal is meant for chopping up small bits of waste food.  When switched on the motor spins and impellers — also called lugs — throw bits of food against a grinder ring. You should always run water while using the garbage disposal; once the garbage disposal does its job, the water flushes the finely chopped particles down the drain.
The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.[19] 

The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.[19]
Similarly, there's no shortage of different types of sinks, too. These range from spare single-bowl models starting under $100 to a farmhouse apron front, double bowl made of copper or cast iron that can run $600 or more. Some are mounted under countertops — called undermount sinks — while drop-in sinks are designed for installation in a preexisting space in your countertop. Whatever the type, sinks can uniquely complement kitchen design as do countertops, cabinetry and other features.
If you decide to try this job yourself, be prepared to keep meticulous track of about a dozen tiny parts (put the stopper in the sink so none of them fall down the drain). There are many different faucet designs, so you may not be able to tell what to replace until you've done the disassembly. Whether you do it yourself or hire a plumber, this would be a good time to think about whether you want to upgrade the faucet with a new design.

Bravo, Don and Zach!! My bathroom was a total mess (leaking!) and with the holidays around the corner I was in desperate need of help. Don careful assessed the situation, walked me thru my options, and kept me aware of the next steps. I was never left wondering “what now?”. As promised, they arrived on-time and ready to begin. My house was kept protected from damage and the work was expertly finished. Warranties were explained and a walk-through revealed all the fine details. I am a fan of good work. Don and Zach exceeded all my expectations. I recommend using Atomic Plumbing to everyone.
Top notch service -- rapid response too!Had a leaky pipe to a washing machine. Called Atomic Plumbing at 8 AM -- they arrived at my house on time and less than 2 hours after my initial call to them. James & Paul were my technicians. Professional, polite, efficient and skilled, they rapidly replaced dated water valves and -- I must say, they did a great job. The repairs not only are functional, but they look great, too!I especially was impressed with the method of pricing. They assess your issue, then provide a flat-fee repair price before any work is done. Their prices are reasonable with no surprises.Highly recommend this company if you want it done right the first time by professionals.
Plumbing is one of your home's main infrastructures - yet water can also be your home's nemesis. So count on True Value Hardware Stores to help you tackle any size plumbing job. From basic projects like installing a new faucet or water filter or opening a clogged drain; to a bit more complex like replacing a water heater, toilet or sump pump, we can help.
Of all the projects homeowners decide to take on themselves, plumbing repairs seem to consistently get them in the most trouble. Every Monday morning, we receive requests to fix weekend plumbing projects that turned out to be more difficult than they first appeared. In more than 40 years serving the Dallas and Fort Worth Metroplex, we’ve seen a lot of unique plumbing problems, making us certain that if you need a plumber to correct a problem, we can fix it right. Call Berkeys to schedule an appointment with a licensed plumber. We serve the entire Dallas / Fort Worth area.
Clogged drains or sewer line backups can wreak havoc on your business, and we know that plumbing emergencies rarely align with business hours. Sudden, unexpected plumbing emergencies can have a serious negative impact on your business—any amount of downtime can result in missed opportunities and the inability to serve your clients, potentially leading to lost revenue. When plumbing emergencies occur at your place of business, you need an emergency plumber you can trust.
×